Differences

This shows you the differences between two versions of the page.

--- fastboot_for_gdos64 [2026/07/20 04:15] – [Copying GD.FBOOT to SoftIEC] Images added fritigern
+++ fastboot_for_gdos64 [2026/07/23 22:25] (current) – ↷ Links adapted because of a move operation fritigern
@@ Line 26: / Line 26: @@
 ==== Using an existing installation ====
-{{ :0:image:gdos64_fastboot_01.png?100|}}First, start GD.CONFIG and set up a RAMDisk of type RAM1581. Alternatively, you can use a RAMNative drive. (RAMNM_S for **S**uperCPU, RAMNM_G for **G**eoRAM, RAMNM_C for a **C**ommodore REU)
+{{ image:gdos64_fastboot_01.png?100|}}First, start GD.CONFIG and set up a RAMDisk of type RAM1581. Alternatively, you can use a RAMNative drive. (RAMNM_S for **S**uperCPU, RAMNM_G for **G**eoRAM, RAMNM_C for a **C**ommodore REU)
 This guide uses drive D, since most older GEOS programs only support drives A and B. This leaves drives A through C free for programs, files, or disk drives.
@@ Line 33: / Line 33: @@
 Next, at least the GDOS64 system files must be copied from the existing boot disk to the RAM drive. To be able to install future updates for GDOS64, you should ensure that there is sufficient free space on the RAM drive. Alternatively, GDOS64 can also be newly installed on the RAM drive. A full installation is recommended!
-{{ :0:image:gdos64_fastboot_02.png?100|}}Next, GD.CONFIG should be launched __directly from the RAM drive__, and the current settings should be saved. To successfully do this, GD.CONFIG should NOT be launched using the ''C= + E'' shortcut or via the GEOS menu, as this may cause GD.CONFIG to launch from a drive __other__ than the RAM drive. Launch GD.CONFIG directly from the RAM drive to save the current settings. If necessary, you can also adjust other settings here. Optionally, you can also change the disk name for the RAM drive.
+{{ image:gdos64_fastboot_02.png?100|}}Next, GD.CONFIG should be launched __directly from the RAM drive__, and the current settings should be saved. To successfully do this, GD.CONFIG should NOT be launched using the ''C= + E'' shortcut or via the GEOS menu, as this may cause GD.CONFIG to launch from a drive __other__ than the RAM drive. Launch GD.CONFIG directly from the RAM drive to save the current settings. If necessary, you can also adjust other settings here. Optionally, you can also change the disk name for the RAM drive.
-{{ :0:image:gdos64_fastboot_03.png?100|}}Next, you need to configure the “GD.FBOOT” boot program. To do this, locate the file on the RAM drive and run it. The configuration is saved in the “GD.FBOOT” file itself. Therefore, it is important for the rest of the process to use this file for the next steps!
+{{ image:gdos64_fastboot_03.png?100|}}Next, you need to configure the “GD.FBOOT” boot program. To do this, locate the file on the RAM drive and run it. The configuration is saved in the “GD.FBOOT” file itself. Therefore, it is important for the rest of the process to use this file for the next steps!
 The startup program is now configured.
@@ Line 41: / Line 41: @@
 ==== Copying GD.FBOOT to SoftIEC ====
-{{ :0:image:gdos64_fastboot_05.png?100|}}Ensure you have installed the GeoDesk module ''Disk Utilities'' and ''Send To...''. To verify, open the GEOS menu and choose Settings -> Edit GeoDesk modules. Installed and active modules have ''*='' in front of their names. If necessary, enable ''Disk Utilities'' and ''Send To...''.
+{{ image:gdos64_fastboot_05.png?100|}}Ensure you have installed the GeoDesk module ''Disk Utilities'' and ''Send To...''. To verify, open the GEOS menu and choose Settings -> Edit GeoDesk modules. Installed and active modules have ''*='' in front of their names. If necessary, enable ''Disk Utilities'' and ''Send To...''.
-{{ :0:image:gdos64_fastboot_06.png?100|}}Verify that you are in the correct directory using “Send Command.” To do this, hold down the ''C='' key and right-click in any drive window.
+{{ image:gdos64_fastboot_06.png?100|}}Verify that you are in the correct directory using “Send Command.” To do this, hold down the ''C='' key and right-click in any drive window.
-In the "Send command" window that now opens, change the drive to 16. Do not change the other settings. The button ''>>? Query status'' will show what the current directory is, and also shows the drive's status (should be ''00, OK,00,00''). {{ :0:image:gdos64_fastboot_07.png?100|}}
+In the "Send command" window that now opens, change the drive to 16. Do not change the other settings. The button ''>>? Query status'' will show what the current directory is, and also shows the drive's status (should be ''00, OK,00,00''). {{ image:gdos64_fastboot_07.png?100|}}
 Change into the directory where you wish to keep the GDOS64 Fastboot files (suggested: /SD/SoftIEC/GDOS64/). The format of changing directories is as follows:
   cd:/SD/dirname
   cd:dirname
   cd:..
-{{ :0:image:gdos64_fastboot_08.png?100|}}Assuming you wish FastBoot to be in /SD/SoftIEC/GDOS64/, find the text box with "Enter command" and in it, type cd:/SD/SoftIEC/GDOS64/ (can be in lower caps) and press the "Send Command" button. The status line should now read ''Disk: 0 "/softiec/gdos64/" 00 2a''
+{{ image:gdos64_fastboot_08.png?100|}}Assuming you wish FastBoot to be in /SD/SoftIEC/GDOS64/, find the text box with "Enter command" and in it, type cd:/SD/SoftIEC/GDOS64/ (can be in lower caps) and press the "Send Command" button. The status line should now read ''Disk: 0 "/softiec/gdos64/" 00 2a''
-{{ :0:image:gdos64_fastboot_10.png?100|}}{{ :0:image:gdos64_fastboot_09.png?100|}}To copy CD.FBOOT to the SoftIEC disk, you now need to right-click GD.FBOOT, and choose ''Send to... >>'' and then ''Options''. In the window that now opens, change the address of Drive#2 to 16, and click ''>2'' button in the bottom right corner.
+{{ image:gdos64_fastboot_10.png?100|}}{{ image:gdos64_fastboot_09.png?100|}}To copy CD.FBOOT to the SoftIEC disk, you now need to right-click GD.FBOOT, and choose ''Send to... >>'' and then ''Options''. In the window that now opens, change the address of Drive#2 to 16, and click ''>2'' button in the bottom right corner.
 You should now exit GDOS64 via the GEOS menu. **DO NOT RESET, REBOOT, OR POWER CYCLE THE C64U AT THIS POINT!**
-{{ :0:image:gdos64_fastboot_12.png?100|}}{{ :0:image:gdos64_fastboot_11.png?100|}}Now open the Ultimate Menu by pulling the rocker switch up, or hit ''C= + RESTORE''. Navigate to where you saved GD.FBOOT, and press ''F1''. Then open ''Power & Reset'' and choose ''Save REU Memory''. Choose a file name (I chose GDOS64) and save the file. It is being saved as GDOS64.REU
+{{ image:gdos64_fastboot_12.png?100|}}{{ image:gdos64_fastboot_11.png?100|}}Now open the Ultimate Menu by pulling the rocker switch up, or hit ''C= + RESTORE''. Navigate to where you saved GD.FBOOT, and press ''F1''. Then open ''Power & Reset'' and choose ''Save REU Memory''. Choose a file name (I chose GDOS64) and save the file. It is being saved as GDOS64.REU
 TIP: Save the current C64U configuration in the GDOS64 folder on your SoftIEC drive. To do this, open the Ultimate Menu, navigate to inside your GDOS64 folder, hit ''F1'' and choose ''Configuration''. Choose "Save to File" and choose a filename. You can now load this configuration before you load GDOS64. Useful when you like to change drive types a lot, or change other config options.